Inexpensive Marrionette Puppet
- Art
- Elementary

- Activity Time
- Materials
- Concepts / Topics
Learners assemble a bird puppet from foam, yarn, fishing line, wood, and bottle caps, add features, and practice controlling its movements.
Puppets, Cheap & Easy: An Easy-to-Make Bird Puppet
By Hal Pederson
These are the text instructions. Critical assembly diagrams could not be included here. You can request them by emailing halped06@verizon.net with "Puppet diagram" in the subject line.
Materials Needed for Each Bird Puppet
- 1 Styrofoam ball, 3 inches in diameter
- 2 Styrofoam balls, 1.5 inches in diameter
- 3 pieces of yarn, 6 to 8 inches long
- 4 pieces of monofilament fishing line, 2 to 3 feet long, depending on the size of the operator
- 2 twist-off bottle caps for the bottoms of the feet
- 2 tongue depressors or equivalent pieces of wood
- 2 thumbtacks or wiggly eyes
- 1 top of a Bic pen for the beak, or part of a Popsicle stick, etc.
- 1 feather for the tail and wings
- A sharp pencil, pen, piece of coat hanger, or knitting needle to make holes in the Styrofoam balls
- Elmer's glue
Step-by-Step Assembly
Use your imagination! You can use recycled materials for the body, head, feet, feathers, eyes, etc.
- Take the large ball and poke holes about 0.5 inches deep around the center, using a pen point, knitting needle, or piece of coat hanger, as shown in Fig. 1 (marked A, B, C, D).
- Take one of the small balls and poke two holes as above, also shown in Fig. 1.
- Take the remaining small ball and cut it exactly in half. A steak knife used like a saw works well.
- Knot three pieces of yarn, about six inches long, at each end.
- Cut four pieces of fishing line about 2.5 to 3 feet long.
- Make a very small slit in each end of the pieces of wood, as shown in Fig. 2.
- Glue one piece of wood about halfway up the other piece of wood, as shown in Fig. 2. Set aside to let the glue dry.
- Take one piece of knotted yarn from Step 4 and insert one end into the small whole ball. Put the other end into hole D on the large ball.
- Use the knitting needle or piece of coat hanger to push in the ends. Squeeze a little glue into these holes.
- Knot a piece of scrap yarn onto one end of each piece of fishing line, then knot the fishing line around the yarn and cut off the excess. This creates a lump at the end so that, once it is glued into the ball, it won't slip out. Stuff this end into hole B of the large ball.
- Repeat the above for the small ball.
- You should have two pieces of knotted yarn left from Step 4. Knot a piece of fishing line onto the yarn knot, as they are going into the same hole. Stuff this end into one of the half-balls (the small ball you cut in half). Squeeze a little glue into the hole. Repeat for the other half.
- Take the other ends of the yarn for these two pieces (yarn only) and stuff one into hole A and the other into hole C.
- You should now have something that looks like Fig. 3. If not, check the steps.
- Insert and tie fishing lines numbered 1 through 4 into the corresponding slits in the wooden pieces, adjusting the length of each line as you go. After you have tied them exactly where you want them, put a little glue on each place to keep them from slipping.
- Squeeze glue into the bottle caps and press them onto the bottoms of the feet (the flat sides of the half-balls). Do this gently so as not to break the Styrofoam.
Finishing Touches
This is the basic puppet. Add eyes, a beak, wings, a tail, and head feathers, using your imagination. Poke a little hole where you want to put the feathers, squeeze in a little glue, and stick in the feathers.
It may take some practice to learn to make it walk, dance, eat something from the ground, sit, and walk backwards, but it can do all of those things, maybe more—it's all up to you.
For assembly diagrams, email halped06@verizon.net with "Puppet Diagrams" in the subject line.
Teachers.Net · https://teachers.net/lessons/3699.html